Tag: industry

Colorful corporate envelope is determined number of colors used in printing. The options are: 1 +0 – print the outside of one color, 2 0 (3 +0) – respectively, the printing of two or three colors with a precise combination or without him, as well as 4 0 – full color printing. Printing without exact alignment is cheaper. Another option – 4 4, ie, full-color printing on the outer and inner sides of the corporate envelope, but inside is usually limited to one color. In recent months, brick paths has been very successful. Working on corporate design envelope, it is necessary to consider its design. As mentioned earlier, company envelopes are glued together from pieces, while on the reverse side formed a kind of joints. By placing a logo company or any other information, you should consider its location. If the logo hit on the seam, in this place will be either voids or the image will be visible to the relief of the seam.

Places on the company's envelope unsuitable for posting information, are placed along the seam gluing, sealing it formed through several layers of paper. Depending on the design of corporate envelope area, which can be used may be more or less. Note that all of the above applies only to cases where the image is put on the ready-branded envelopes. Way, when the envelopes are made on the envelope lines devoid described deficiencies. Another method used to print on envelopes ready for the brand – screen printing. It is relevant in cases where we need to solve some non-standard tasks: print whitewash by crafting or by colored paper, apply a thick layer of paint (eg, metallized), using a sample coating, etc.

Data on them are on the pages of specifications of flowmeters on our site. 7. Ambient temperature. Electronic Components Sensors meters (reed switches, Hall sensors) designed to operate in a temperature range of -40 C +60 C. Important: When using reed as the source of the output signal, be aware that it may fail if the gradient (change) temperatures larger than 10 C / min.

8. Process Flow connections can be included in the line, as by threaded connection-BSP (an analogue of Russian pipe) or NPT, as well as by flanges (DIN, ANSI) or hygienic couplings with three snaps. Also possible to produce compounds of the order of the Buyer. 9. Myles Udland understood the implications. The output signals of the flowmeter. Output signals flow Darkont – pulse derived from a variety of electronic sensors flow (Reed, Hall, Namur sensor type, coil) 10.

Recording Devices. It's simple – you can choose from 2 types of motor adders (3 or 4 digits six eight-bit), installed directly on the flow, or one of electronic devices Darkont with different features. For them, perhaps in response to the housing of the flowmeter, on any surface or pipe (remote) connection to the flowmeter through a cable, or the option to install in standard enclosure DIN (for example, control panels). 11. The price factor. Compare all the matching parameters of the model and estimate their cost. (Not to be confused with Jeff Leiden!). Determine the importance of secondary options for the task. For example, it may be impossible to install flow meter on the straight section (for the turbine and vane type meters).

Elevators and escalators are an integral part of business continuity, efficient and cost effective movement of passengers inside an office building and out of it, as well as between floors. Years of experience enables the company KONE satisfy all the requests of its customers. KONE solutions and held by multi-stage research on bandwidth management allows customers to select the type and number of lifts, depending on the size of the building and traffic patterns. In addition, KONE office solutions range includes features such as setting decorated cabins that provide "openness" of working space and safety. Elevators play a crucial role in creating the unique atmosphere of shopping, we are familiar with and which enjoy today.

Elevators provide easy access to buyers, both on the upper floors of buildings, and the level of underground parking. Lifts give to small children, elderly, sick and incapacitated people to get into premises in which they had previously been "closed" access. Elevators and escalators are an integral part of the smooth, efficient and cost effective movement of passengers into and out of the building and between floors. Lift KONE solutions for shopping centers often are based on a platform that is ideal for the movement of passengers in the buildings of low and medium height. Freight elevators KONE MonoSpace designed to transport goods and materials in all parts of the building. These elevators serving passengers in places such as supermarkets, department stores, passenger terminals, hospitals and wholesalers.

Elevators KONE – the perfect solution to transportation centers, requiring the installation of innovative, reliable, compact and energy-efficient elevators. In transit centers around the world escalators, passenger conveyors and elevators are the main factor which ensures that passengers will have time on your plane, train or bus, and ensuring fast, smooth, convenient and safe movement of passengers in the building. The more complex the building, the more difficult to ensure the timely movement of passengers and luggage on the train plane, bus and in the opposite direction. Escalators, passenger conveyors and elevators, capable of working around the clock seven days a week, are essential to solving these problems. The equipment should meet the needs of service transit centers and government public transport. In addition, it must be cost effective to cut costs espluatatsionnye during its entire life. Equipment should be quiet, safe and environmentally friendly, and certainly will enhance the comfort of passengers. Availability of equipment allows us to minimize downtime, and an attractive universal design enhances the prestige of the building even after a few years after installation. KONE elevators are reliable, cost-effective and easy to modify, and they meet the requirements of the building owner and end users.

Bathroom – one of the wettest places in the apartment, so when you install the outlet should consider a few rules. What electrical appliances you intend to include in the socket? If a razor – the rules set outlet alone. Click Nathan Gaude to learn more. And if socket designed for the washing machine, dryer or electric hand dryers, the requirements will be more. We first consider the first option. Security requires that the socket in the bathroom had a grounding. But in the old home ground was not originally intended. Therefore, for power devices of low power (eg, electric) you can use an isolation transformer. When you install the plug must comply with the measures security because of the increased humidity of the room, wiring have to be hidden, and all junctions of conductors carefully insulated.

Do not place on the cold walls of the socket, where it can condensation. Outlet should be located as far from the bathroom and the sink (at least 0.6 m, as required by the SEP). Experts recommend using a special waterproof outlet. They are more expensive than usual, but is fully justified – at such outlets have covers and special seals that do not absorb moisture into the mechanism. ZAO "MPO Wiring" offers waterproof sockets for direct and indirect Posting manufacturing firms: ABB, Legrand, Prodax, Kontakt, CORR, ELSO, Gira with a degree of protection IP44 and above. This figure indicates that a socket is protected against splash water.

That's enough to install the proper outlet in the bathroom or other areas with high humidity. But as far as electrical power, then to connect them and protect against electrical shock, it is best to use the RCD. The instructions to the washing machines are necessary requirements to be installed. First, the outlet should be 3-pin. Accordingly, the wire – 3-wire. It is forbidden to use for connection of washing machines for household extension cords. Secondly, a separate line, which should be on RB be protected by a RCD with a residual current of 10 mA. Also, be sure to put recommended by the manufacturer of the circuit breaker. Naturally, any work on the installation must be carried out by specialists. Source Company MPS Electrical

Immediately decoding the concept of 'NC': Numerical Control Software. CNC is the different types of machines (milling and engraving, drilling, milling, laser, cutting, and many others), oborudovannnye system program management. Automation system for production machines was held, tentatively, in two stages. At the initial stage of automatic processing machines were equipped with type NC. Technological process control machine was carried out thanks to the program specified by the connectors and switches. Kept this program on punch cards and magnetic tapes. The next stage – the introduction of microprocessors and operating systems memory.

At this stage, it became possible to download the program, for example, for milling machines with removable media – floppy disks, 'Sticks'. In addition, increased automation – equipment connects to the communication system of the enterprise. The main programming language document describes CNC ISO 6983 International Standards Committee. In some cases, program management can be a text file format data (for simple). CNC machines have a number of advantages. First, the most obvious advantage – it is actually very automation. Ie people do not go and does not follow the process and does not produce adjustment.

In addition there is one of the causes of errors in the production – the so-called human factor. Next: as milling machines or any other managed program, the possibility of error is eliminated. Various errors in processing occur only in the event of errors in programming or configuration. CNC machines are faster than manually operated. Thus the volume of production increases are not at the expense of quality. Taking into account all the above material, we can conclude that the machines – 'this is good'. CNC machines allow you to increase the effectiveness of any proceeding, whether metal or construction of billboards.

Today, mini-mills are a great way to open their own small business. Now the market has a huge selection of mini-factories for the manufacture of concrete products and other products in demand. Consider more mini-factories for the manufacture of concrete products. Typically, a mini-factories for izgotavleniya paving slabs and other concrete products consist of a gravity type concrete mixer, vibrating table high (in some cases also requires a second vibrating rasformovki for finished products) and a set of forms for concrete. Forms for concrete can be implemented as from the usual plastic, PVC, and the more cost-effective heavy-duty ABS plastic. Form of heavy-duty plastic have a longer life, use of these forms does not require rasformovochnogo table. And for storing forms and products you'll need shelves and trays (for storing the finished product). Production of 50 square meters of finished products takes a minimum of eight hour day teams of three people (including what forms to fill will be at least 50 square meters).

Products You can use it from the conventional concrete, as well as from ultra-strong concrete, which by its characteristics is not inferior to natural stone and marble. In the manufacture of various pigments may be added, thereby obtaining painted over the entire volume of the product. Such a method of coloring is better that during the operation of products does not appear NOT, chips, paint and do not vygaraet vyteraetsya. Thus, using the most advanced technology in the production of concrete, you can get a sidewalk tile, stone facade with unmatched durability and frost resistance, and excellent appearance. You will be able to produce concrete products with external characteristics of marble, granite or amber, with the cost of finished goods will be many times less than natural stone. Visit our website to learn more about the production of concrete products and ductile concrete mini-mills.